Galvanized to Pex


For some of us who had our homes built years ago, there are chances your plumbing system has galvanized pipes.

Galvanized to Pex Overview

 Pex

And one primary problem with these pipes is that they rust and start making leaks soon. oN the hand, pex pipes are not subjected to the calcium build-up issues, so someone can replace the worn-out and leaking galvanized pipes with pex. Fortunately, Pex pipes are easy to install and purchase.
Material you need

  • Two Pipe wrenches
  • Teflon tape- this one for wrapping threading right on adapters
  • Plastic tubing cutter/PVC- used for cutting out your pex
  • Pex piping – you will need pex piping inches, and size will depend on the diameter of current pipes alongside the length of your pipes. further, you can get blue, red, or white the difference is only that blue is utilized to identify cold water, red hot water, and white either.
  • Plastic sheeting – Have it under your pipes to protect your wood and insulation.
  • Sharkbite pex adapters
  • Flashlight
  • Saw to cut metal
  • Water meter key
  • WD40
  • Trays typically catch water drips. You will at least require two trays to catch water on big projects and plastic up just to be safe.
    A quick guide to follow
    Step 1: Turn off the water
    Do it directly from the major water valve and also at the meter utilizing your water meter key. his ensures you are safe.
    Step2: Run all showers and faucets to empty water from the
    These are the hose faucets that you usually keep outside. ensure to leave them open until you are fully done with this project to be safe.
    Step 3: Prep the area
    At this point, lay down the plastic wrap followed by a shallow tray right under the spot you want to cut. further, ensure you got around two trays on your hand to eventually catch water.
    Step 4: Cut the metal
    Now using the saw, cut your galvanized old pipe. You will notice some water come out, so don’t panic.
    Step 5: Buts out WD40
    Just spray it on joints where pipes were connected to break up rust.
    Step 6: Unscrew pipe ends
    Utilize your two pipe wrenches while pulled in the opposite directions. One should be gripping the pipe you will be unscrewing and the other one gripping a specific joint you will be unscrewing it from.
    Step 7: Now prep your PEX adapter
    Consider wrapping it using Teflon tape clockwise
    Step 8: Next screw adapter to the joint you previous unscrewed your pipe right from
    Step 9: Cut clean edge on PEX using PVC cutter also, mark one inch starting from the end
    Step 10: You are almost done! straighten the PEX followed by running it along the pipe length you are replacing
    Step 11: You are required to push the end of the PEX to the adapter till you eventually reach the one-inch mark you marked earlier.
    Step 12: Repeat a similar thing right another joint; you are done!
    Final word
    With the above guide, you will successfully replace your leaking galvanized pipes with PEX. Hope the step-by-step guide helped you?

How Do You Transition From Galvanized to PEX?

Luckily, there are a number of ways to transition from galvanized to PEX without ripping up your old piping. These include using support clips at the bifurcation joints and fitting transition adapters at valve joints. In addition, you can easily identify PEX tubing by scraping it with a flathead screwdriver or coin. If you’re unsure, you can also use a metal sander to remove rough edges.

Galvanized to Pex

Once you’ve made the decision to switch from galvanized pipe to PEX, you’ll need to decide how you’re going to transition. Many plumbers use SharkBite push to connect fittings. These can’t be press-fit onto the galvanized pipe, so you will need to square-cut your galvanized pipe to fit it. Then, thread the PEX pipe into the transition adapter using a compatible method.

To make the transition from galvanized to PEX, you’ll need to make sure that your water main valve can handle enough water to transition to PEX. If it can’t handle the change, you’ll have to buy a new water main valve to accommodate the change. After that, connect the PEX pipe to the fitting using a compatible method. To make the transition from galvanized to PEX even easier, you can use an Economy Plumbing Service to re-pipe your entire house in two days. Learn more about coss linking polyester here.

Using a compression splint with PEX pipe is another option. This fitting has a threaded end on one side and a cut end on the other. You can easily use a compression splint if you have multiple connections and want to change the pipes in the future. If the transition isn’t complete, you can use a compression splint to connect the old pipe with the new one.

Can I Connect PEX to Galvanized?

Yes, it is possible to connect PEX to galvanized. Before you start connecting the two, you need to prepare both pipes properly. Ensure the PEX pipe has a clean and straight cut. Then, align the joint with pencil lines to make sure that the coupling will fit correctly.

Copper pipes do not require support sleeves. Just make sure that the exterior of the PEX pipe is smooth and free from scratches. If you are unsure of how to connect these two materials, you can look up more information on YouTube or read articles online. Read about cleaning polyester here.

Recent Posts